Acer H236HL Service Manual Download Page 52

Page: 52 / 59

8. FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Acer

H236HL. Refer to

this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

Please note that WHEN ORDERING FRU PARTS, you should c heck the most up-to-date information available on

your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the

printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT

part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list

provided by your regional Acer office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on

how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Picture

Description

LNT Part No.

Acer Part No.

bezel A34G3021AEM-1B0100

42.LX1M2.001

PANEL LM230WF3-S2E2

750GMT230W3E21N100 KL.2300W.002

mid-frame ASSEMBLY

705GFACS307

60.LX1M2.005

KEYPAD BOARD

KEPCCQYO

55.LX1M2.002

Summary of Contents for H236HL




























































Search results

Summary of Contents for H236HL

Reviews:

Related manuals for H236HL

Brands by name

Popular brands

Acer H236HL, Service Manual

Search results

Summary of Contents for H236HL

Reviews:

Related manuals for H236HL

Brands by name

Popular brands