Acer AL1717 Page 10 Service Manual Download

Page: 10 / 73

- 10 -

LCD monitor General specification

Panel Type:

17 “ active matrix color TFT LCD

1). LG HT17E01-A05

2). Toppoly TD1402

Display size:

37.92mm

(H)

270.34mm(V)

Display mode:

VGA 720

400 (70 Hz)

VGA 640

480 (60/66/70/72/75 Hz)

SVGA 800

600 (60/70/72/75 Hz)

XGA 1024

768 (60/70/75 Hz)

SXGA 1280

1024 (60/70/75 Hz) standard resolution

Pixel pitch:

0.264mm(H)

0.264mm(V)

Display Dot:

1280 x (RGB)

1024

Pixel Clock:

25.2

–

135.0MHz

Contrast ratio:

= 0

LG 450 : 1 , TOPPOLY 450 :1

Brightness:

LG:250, TOPPOLY 260(typical)

Response time (Tr/Tf):

LG(16), TOPPOLY (12)

Display color:

16.2M(6 bit color+FRC)

Viewing angle:

LG L / R

≧

70 /

≧

70 (

≧

140 degrees horizontal typical)

U / D

≧

60 /

≧

60(

≧

120 degrees vertical typical)

TOPPOLY L / R

≧

75 /

≧

U / D

≧

75 /

≧

Luminance Uniformity:

> 75 % (typical)

Pc interface:

1).Video: RGB analog 0.7V peak to peak

Sync: TTL positive or negative

Signal connector:

15 pin Mini D type, (standard VGA video)

3.5 mm stereo audio jack (Audio) (For AR577 only)

Audio power:

0.5Wrms + 0.5Wrms (300Hz – 10kHz (S.P.L. – 10 dB))(AA677 only)

Front control:

power on/off with LED select adjustment (+,-)

Interface frequency

Horizontal Frequency

24KHz

--80KHz

Vertical Frequency

49Hz ------75Hz

Plug & play:

Support VESA DDC2B functions

Power Input voltage:

Single phase, 50/60HZ, 100 VAC to 240VAC

10%

Total output power:

40 Watt max.

Summary of Contents for AL1717










































































Search results

Summary of Contents for AL1717

Reviews:

Related manuals for AL1717

Brands by name

Popular brands

Acer AL1717, Service Manual

Search results

Summary of Contents for AL1717

Reviews:

Related manuals for AL1717

Brands by name

Popular brands