background image

 

46

Chapter 6 

FRU (Field Replaceable Unit) list                                             

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL1515 m. Refer to this 

chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). 

NOTE : Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available 

on your regional web or channel(

http://aicsl.acer.com.tw/spl/

). For whatever reasons a part number change is 

made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your 

Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service 

Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and 

service of customer machines. 

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on 

how best to dispose it, or follow the rules set by your regional Acer office on how to return it. 

Summary of Contents for AL1515






























































Reviews: