Acer AL1515 Page 30 Service Manual Download | Manualshive

Page: 30 / 61

background image

- 30 -

Chapter 2

Operating Instructions

CONTROLS

Control panel (monitor front panel)

1. Power ON/OFF switch, push to ON and push to OFF. (Toggle switch)

2. Power LED will be blue when monitor is on; be amber when in power saving mode.

3. Menu.

4. Adjust increase (Function select).

Adjust decrease (Function select).

5. Auto adjustment Buttons.

Note:

1. Press button 4 (plus +) or (minus -) at the same time can activate “Volume Adjustment”.

2. When OSD Menu is off, press button 5 (auto) at the same time can activate “Auto Adjustment” immediately.

3. When into Factory mode press 4 (plus +),(minus -) and 1 (power) together 2 seconds at same time.

5. When into Burning mode press 5 (menus), 1 (power) together 2 second at same time.

«
...
28
29
30
31
32
...
»

Summary of Contents for AL1515






























































Reviews:

No comments

Related manuals for AL1515

Brand: Garmin Pages: 16

Brand: I-Tech Pages: 27

Babyruf MBF 3838

Brand: H&H Pages: 6

ErgoAct OEM Monitor

Brand: Intergraph Pages: 18

Brand: Barco Pages: 78

Brand: CORNEA Pages: 20

Q72B - Optiquest - 17" LCD Monitor

Brand: ViewSonic Pages: 2

Brand: ViewSonic Pages: 107

Brand: Sanitas Pages: 80

Brand: Barco Pages: 71

Brand: BenQ Pages: 36

Brand: Hanns.G Pages: 20

Brand: NA-DE Pages: 4

Brand: Barco Pages: 64

DisplayPort DPA-400

Brand: Unigraf Pages: 34

Brand: ADCMT Pages: 306

Brand: Planar Pages: 18

Brand: Xenarc Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands