ACD CAL-101 Instruction Manual Download Page 13

IX. STANDARD WARRANTY 

We warrant gas calibration equipment manufactured and sold by us to be 

free from defects in materials, workmanship and performance for a period 

of one year from date of shipment.  Any parts found defective within that 

period will be repaired or replaced, at our option, free of charge, F.O.B. 

factory.  This warranty does not apply to those items which by their nature 

are subject to deterioration or consumption in normal service, and which 

must be cleaned, repaired, or replaced on a routine basis.

Such items may include:

 

a. 

Electrochemical type generating cells

  b. Batteries

Warranty is voided by abuse including rough handling, mechanical damage, 

alteration, or repair procedures not in accordance with the instruction 

manual.  This warranty indicates the full extent of our liability, and we 

are not responsible for removal or replacement cost, local repair costs, 

transportation costs or contingent expenses incurred without our prior 

approval.

Advanced Calibration Designs, Inc.’s obligation under this warranty shall 

be limited to repairing or replacing, and returning any product which shall 

be returned to Advanced Calibration Designs, Inc. at its manufacturing 

facilities, with transportation charges prepaid, and which Advance Calibration 

Designs, Inc.’s Material Review Board examination shall disclose to its 

satisfaction to have been defective.

This warranty is expressed in lieu of any and all other warranties and 

representations, expressed or implied, and all other obligations or liabilities 

on the part of Advanced Calibration Designs, Inc. including, but not limited to, 

the warranty of fitness for a particular purpose.  In no event shall Advanced 

Calibration Designs, Inc. be liable for direct, incidental or consequential loss 

or damage of any kind connected with the use of its products or failure of 

its products to function or operate properly.

The following is a listing of the available electrochemical CAL-101 cells 

and their standard warranty when installed in equipment manufactured and 

supplied by Advanced Calibration Designs, Inc. 

Chlorine, Hydrogen, Hydrogen Sulfide, and Hydrogen Cyanide

 

- 2 Hour Cell -  2 hour of 

use

Page 11

Summary of Contents for CAL-101
















Reviews: