background image

Installation & Operation Manual - Model AVC6000 

Contents of this Manual are Subject to Change Without Notification

 

Page   6 

SECTION 2 

 SPECIFICATIONS 

PERFORMANCE 

 

Accuracy 

+/- 5% of reading or 5 CFM, whichever is greater 

Speed of Response 

< 1 second control signal response (full stroke cycle time based on actuator type) 

Shut-off Leakage Rate 

Standard:  < 1.5% FS at max operating pressure 

 

"S" Option: < 0.5% FS round valves, < 1% FS rectangular valves @ max operating pressure 

Max Operating Pressure 

3”wc Differential Pressure Across Valve

 

Min Operating Pressure 

Reference Section 2.1 

Airflow Range 

Reference Section 2.1 

Failure Mode 

Open, Closed or Last Position (based on actuator type selection) 

ENVIRONMENTAL 

 

Temperature 

Airstream: -20 to 165 deg. F for all Standard Valve Models 

 

                    -20 to 375 deg. F for the High Temp SS Valve Models 

 

Ambient:   -20 to 125 deg. F      Storage:     -40 to 165 deg. F 

Humidity 

0 to 90% non-condensing 

ELECTRICAL 

 

Input Power 

24VAC +/- 20% 50-60Hz or 24 VDC +/- 10% 

 

Max Power for Valve Size 06-24: 28VA or 16W for units with actuator type 3 & 5 

 

                                                           11VA or 7W for units with actuator type 7 

 

Max Power for Valve Size 36, 48: 51VA or 29W for units with actuator type 3 & 5 

 

                                                            17VA or 11W for units with actuator type 7 

 

If monitor FHM1 is connected to AVC, increase above values by 3VA or 1W 
If monitor FHM3 is connected to AVC, increase above values by 6VA or 3W 

Analog Inputs 

AI-1; Software Configurable for Voltage or Current, 12-bit resolution 

 

Voltage: 0-10Vdc Range, 1M ohm Impedance 

 

Current: 0-20mA Range, 500 ohm Impedance 

 

AI-2, AI-3; Software Configurable for Resistance range of 20K ohm or 100K ohm 

 

500uA Current Source for 20K ohm Range, 100uA Current Source for 100K ohm Range 

Digital Inputs 

DI-1 and DI-2; Dry-contact inputs 

Analog Outputs 

AO-1 and AO-2; Software Configurable; 0-20mA, 4-20mA, 0-10v, 2-10v, 0-5v or 1-5v 

 

12-bit Resolution, capable of driving 1K ohm load 

Alarm Relay Output 

SPST, NC/NO contacts, rated load 1A @ 30 vDC or 0.3A @ 125vac 

 

Max operating voltage = 125VAC or 60 vDC 

 

Max carry current = 1A, Max switching capacity = 37 VA, 30W 

Network Com Port 

EIA 485 2-wire BACnet MS/TP 

 

Full Master Node State Machine 

 

Data Rates 9600, 19200, 38400, 76800 and 115200 

 

Mac address is software configurable 

 

¼ Unit Load Receiver Input Impedance, bias & EOL termination not provided within the AVC 

Configuration Port 

USB 2.0, Isolated, Type C Connector, Optional Bluetooth (Ver 4.2 or later) 

Status Indicators 

LED Indicators for Power, Alarm, AO, BACnet, USB, AVC Status, Bluetooth & AccuNet 

I/O Terminal Blocks 

2 and 3 position vertical pluggable screw terminal blocks 

Electromagnetic 

EMC Directive 2004/108/EC 

Compatibility 

Low Voltage Directive 2004/108/EEC 

 

EN61326-1:2013 

Summary of Contents for ACCUVALVE AVC6000











































































Reviews: