AccuTemp Accu-Steam G2 Series Installation & Operator'S Manual Download Page 5 | Manualshive

Page: 5 / 39

background image

MP5017-2002

Accu-Steam Gas Griddle

4

The safety instructions listed below on this page should be posted in a

prominent location as a reminder of safe practices as well as recommended

actions to follow in the event of an equipment or facility utility issue.

In the event a gas odor is detected, shut down all appliances at the main gas shut-off valve
and contact the local gas company or gas supplier service.

1.1 IMPORTANT FOR YOUR SAFETY

WARNING

In the event of a power failure, do not attempt to operate this appliance.

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or
any other appliance.

Improper installation, adjustment, alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating, and maintenance instructions
thoroughly before installing or servicing this equipment.

Only qualified service technicians/electricians should install this appliance to ensure that all
electrical and safety requirements are met and that all wiring is installed in accordance with
all national, state and local electrical codes.

WARNING

WARNING

WARNING

WARNING

«
...
3
4
5
6
7
...
»

Summary of Contents for Accu-Steam G2 Series








































Reviews:

No comments

Related manuals for Accu-Steam G2 Series

EGD Series S/N 7547

Brand: AccuTemp Pages: 50

Brand: Salvis Pages: 2

Brand: Menu System Pages: 44

MIRACLEAN PRE-2000

Brand: Keating Of Chicago Pages: 22

Brand: Keating Of Chicago Pages: 27

Brand: Bartscher Pages: 28

Brand: Falcon Pages: 6

Double Play 5650

Brand: Char-Griller Pages: 56

Blue Seal Evolution Series GP518-B

Brand: Moffat Pages: 2

ACCU-MISER AM24

Brand: Toastmaster Pages: 34

Grill, Griddle & Waffle

Brand: GreenPan Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands