Accurex Lysun RFM-101 User Manual Download Page 40

Page: 40 / 41

Versions 1.0

Appendix 3 Warranty

Please complete the warranty card included in the packaging. Mail it to your local

distributor to register your purchase within 30 days of purchase.

Note: This warranty applies only to the meter in the original purchase. It does not

apply to the other materials included with the meter.

Hangzhou Lysun Biotechnology Co., Ltd. warrants to the original purchaser that this

meter will be free from defects in materials and workmanship for a period of two

years (24 months) since the latest date of original purchase or installation, except as

noted below. Within the prescribed two years, Lysun Biotechnology Co., Ltd. shall

replace the meter under warranty with a reconditioned meter, at its option, repair

at no charge if a meter that is found to be defective. Lysun Biotechnology Co., Ltd.

shall not be responsible for shipping charges incurred in the repair of a meter.

This warranty is subject to the following exceptions and limitations:

This warranty is limited to repair or replacement due to defects in parts or

workmanship. Parts required which were not defective shall be replaced at

additional cost. Lysun Biotechnology Co., Ltd. shall not be required to make any

repairs or replace any parts that are necessitated by abuse, accidents, alteration,

misuse, neglect, failure to operate the meter in accordance with the user’s manual,

or maintenance by anyone other than Lysun Biotechnology Co., Ltd. Furthermore,

Lysun Biotechnology Co., Ltd. assumes no liability from malfunction or damage to

meters caused by the use of devices other than devices manufactured by Lysun

Biotechnology Co., Ltd. Lysun Biotechnology Co., Ltd. reserves the right to make

changes in the design of this meter without obligation to incorporate such changes

into previously manufactured meters.

Disclaimer of Warranties

This warranty is expressly made in lieu of any and all other warranties expressed

RFM-101 insert 20191125.indd 38

2019/11/27 10:42:08

Summary of Contents for Lysun RFM-101










































Search results

Summary of Contents for Lysun RFM-101

Reviews:

Related manuals for Lysun RFM-101

Brands by name

Popular brands

Accurex Lysun RFM-101, User Manual

Search results

Summary of Contents for Lysun RFM-101

Reviews:

Related manuals for Lysun RFM-101

Brands by name

Popular brands