Accurate Locators XL16 IMAGER User Manual Download Page 15 | Manualshive

Page: 15 / 67

background image

Connecting the XL-16 Imager Pro Control Unit

On the face of the Control Unit, several ports can be connected.

*The XL-16 Imager does

Not utilize all of the port connections.

1

2

3

Wireless adapter

1. Connect Antenna to the Imaging Port (Com2)
2. Connect the Power connector
3. Plug in the RJ-45 into the ETHERNET port
4. USB for wireless connection device(s).

*Presently the Control Units do not use COM1, COM3.

Your XL-16 Imager package Field pack will be fully assembled tested and your Lap Top will be fully
configured. You are able to use your equipment immediately out of the box. It is highly recommended
that you take at least a few weeks and practice with your USA series detector for best technique and
detection results. Always check the above connections show in the picture before you turn on your
control unit. This will help avoid any operating issues. *Note some minimal assembly will be required.*

VERY IMPORTANT

:

DO NOT DISCONNECT / CONNECT ANY OF THE CABLES WITH POWER CONNECTED
FAILURE TO DO SO CAN CAUSE DAMAGE TO INTERNAL CIRCUITRY AND VOID
WARRANTY.

SAFETY PRECAUTION

Do not let end of battery connection hit metal

- 15 -

«
...
13
14
15
16
17
...
»

Summary of Contents for XL16 IMAGER




































































Reviews:

No comments

Related manuals for XL16 IMAGER

Brand: XP Metal Detectors Pages: 2

Brand: Triple Plus Pages: 16

Brand: CREDO DDM Pages: 17

Brand: Steinberg Systems Pages: 145

Brand: DeepTech Pages: 24

Brand: Valentine One Pages: 20

Brand: Eastern Energy Pages: 4

Brand: Nautilus Pages: 4

GAS-EXPLORER OM-0517

Brand: Bascom_turner Pages: 28

Brand: RC Systems Pages: 10

Brand: RC Systems Pages: 51

Brand: Adams Pages: 2

Brand: Metal Defender Pages: 19

Brand: Sears Pages: 12

Brand: Sears Pages: 12

321.596270 Amphibian

Brand: Sears Pages: 10

Brand: Sears Pages: 11

Brand: Sears Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands