background image

 

  3075-GS ZOOM STEREO MICROSCOPE ON GEM STAND   

 

 

 

         

 

         

ACCU-SCOPE

          73 Mall Drive, Commack, NY 11725  •  631-864-1000  •  www.accu-scope.com 

13

 

 

MAINTENANCE 

Please remember to 

never

 

leave the microscope with eyepieces removed and always protect the 

microscope with the dust cover when not in use. 

 

 

 

SERVICE 

ACCU-SCOPE

  

microscopes are precision instruments which require periodic servicing to keep them 

performing properly and to compensate for normal wear. A regular schedule of preventative maintenance 

by qualified personnel is highly recommended. Your authorized 

ACCU-SCOPE

  

distributor can arrange 

for this service. Should unexpected problems be experienced with your instrument, proceed as follows: 

 

1. Contact the 

ACCU-SCOPE

  

distributor from whom you purchased the microscope. Some problems 

can be resolved simply over the telephone. 

 

2. If it is determined that the microscope should be returned to your 

ACCU-SCOPE

  

distributor or to 

ACCU-SCOPE

 

for warranty repair, pack the instrument in its original Styrofoam shipping carton. If you no 

longer have this carton, pack the microscope in a crush-resistant carton with a minimum of three inches 

of a shock absorbing material surrounding it to prevent in-transit damage. The microscope should be 

wrapped in a plastic bag to prevent Styrofoam dust from damaging the microscope. Always ship the 

microscope in an upright position; 

NEVER SHIP A MICROSCOPE ON ITS SIDE

. The microscope or 

component should be shipped prepaid and insured. 

 

 

LIMITED MICROSCOPE WARRANTY

 

This microscope and its electronic components are warranted to be free from defects in material and workmanship 

for a period of five years from the date of invoice to the original (end user) purchaser.  The LED lamp is warranted 

for a period of two years from the date of invoice to the original (end user) purchaser.  This warranty does not cover 

damage caused in-transit, misuse, neglect, abuse or damage resulting from improper servicing or modification by 

other then ACCU-SCOPE approved service personnel.  This warranty does not cover any routine maintenance 

work or any other work, which is reasonably expected to be performed by the purchaser. Normal wear is excluded 

from this warranty. No responsibility is assumed for unsatisfactory operating performance due to environmental 

conditions such as humidity, dust, corrosive chemicals, deposition of oil or other foreign matter, spillage or other 

conditions beyond the control of ACCU-SCOPE INC.  This warranty expressly excludes any liability by ACCU-

SCOPE INC. for consequential loss or damage on any grounds, such as (but not limited to) the non-availability to 

the End User of the product(s) under warranty or the need to repair work processes.  Should any defect in material, 

workmanship or electronic component occur under this warranty contact your ACCU-SCOPE distributor or ACCU-

SCOPE at (631) 864-1000.  This warranty is limited to the continental United States of America.  All items returned 

for warranty repair must be sent freight prepaid and insured to ACCU-SCOPE INC., 73 Mall Drive, Commack, NY  

11725 – USA.  All warranty repairs will be returned freight prepaid to any destination within the continental United 

States of America, for all foreign warranty repairs return freight charges are the responsibility of the 

individual/company who returned the merchandise for repair.  

 

ACCU-SCOPE is a registered trademark of ACCU-SCOPE INC., Commack, NY 11725 

 

Summary of Contents for 3075-GS















Reviews: