background image

GPI is a registered trademark of Great Plains Industries, Inc.
© 2010 by GREAT PLAINS INDUSTRIES, INC., Wichita, KS

Printed in U.S.A.    04/10

Rev. -  920863-01

Limited Warranty Policy

Great Plains Industries, Inc. 5252 E. 36

th

 Street North, Wichita, KS USA 67220-3205, hereby provides a limited warranty against defects in mate-

rial and workmanship on all products manufactured by Great Plains Industries, Inc. This product includes a 1 year warranty. Manufacturer’s sole 

obligation under the foregoing warranties will be limited to either, at Manufacturer’s option, replacing or repairing defective Goods (subject to 

limitations hereinafter provided) or refunding the purchase price for such Goods theretofore paid by the Buyer, and Buyer’s exclusive remedy for 

breach of any such warranties will be enforcement of such obligations of Manufacturer. The warranty shall extend to the purchaser of this product 

and to any person to whom such product is transferred during the warranty period.
The warranty period shall begin on the date of manufacture or on the date of purchase with an original sales receipt. This warranty shall not apply if:

A.  the product has been altered or modified outside the warrantor’s duly appointed representative;

B.  the product has been subjected to neglect, misuse, abuse or damage or has been installed or operated other than in accordance with 

the manufacturer’s operating instructions.

To make a claim against this warranty, contact the GPI Customer Service Department at 316-686-7361 or 888-996-3837. Or by mail at:

Great Plains Industries, Inc.

5252 E. 36

th

 St. North

Wichita, KS, USA 67220-3205

The company shall, notify the customer to either send the product, transportation prepaid, to the company at its office in Wichita, Kansas, or to 

a duly authorized service center. The company shall perform all obligations imposed on it by the terms of this warranty within 60 days of receipt 

of the defective product.
GREAT PLAINS INDUSTRIES, INC., EXCLUDES LIABILITY UNDER THIS WARRANTY FOR DIRECT, INDIRECT, INCIDENTAL AND CONSEQUEN-

TIAL DAMAGES INCURRED IN THE USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER.
The company herewith expressly disclaims any warranty of merchantability or fitness for any particular purpose other than for which it was designed.
This warranty gives you specific rights and you may also have other rights which vary from U.S. state to U.S. state.
Note: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT – Part 702 (governs the resale availability of the warranty terms). 

AUTHORIZED DISTRIBUTOR:

Summary of Contents for TM Series





























Reviews: