background image

 

4

 

    

         General Warnings ---------------          

 

 

 

1. 

Keep this Instruction Manual available 
for future reference. 

2. 

These instructions must be observed 
to ensure the safe and effective use of 
this bed and the safety of users and 
caregivers. 

3. 

This bed must be assembled, 
positioned and used in accordance 
with these instructions. 

4. 

The safety features for operating the 
bed and instructions concerning the 
bed must be strictly observed. 

5. 

This bed must not be exposed to 
smoke, naked flame, extreme 
temperature, flammable gases or other 
hazardous substances or situations. 

6. 

Do not smoke in or around the bed. 

7. 

Accora shall not be held liable for any 
damage, injuries or accidents arising 
from unauthorised modifications, non-
genuine spare parts, negligence or 
use that is at variance with this manual 
which can result in serious injury or 
death. 

8. 

Electrical equipment can be hazardous 
if misused or abused. Ensure the 
electrical supply cable is not damaged 
by crushing and does not create a trip 
hazard. 

9. 

Inappropriate routing of accessory 
cables, e.g. mattress air pump cable, 
could lead to dangerous electric 
hazards if squeezed or crushed 
between moving parts. The bed must 
not be used if there is any visible 
damage to any cables. 

10. 

When routing cables for other 
electronic equipment used with the 
bed (e.g. air mattress pump), ensure 
cables cannot be squeezed, crushed 
or damaged by the moving parts on 
the bed. 

11. 

Inappropriate use of the power supply 
cable (e.g. kinking, shearing) could 
lead to dangerous electric hazards. 
The bed must not be used if there is 
any visible damage to this cable. 

12. 

 

12. 

The hand control should be positioned 
to avoid strangulation risk. 
Inappropriate use of the hand control 
(e.g. kinking, shearing) could lead to 
dangerous electric hazards. The bed 
must not be used if there is any visible 
damage to the handset or cable. 

13. 

Electrical installations must meet local 
requirements. 

14. 

Only use side rails, and other 
accessories, that are compatible with 
this bed as supplied by Accora. 
Incompatible side rails can create 
hazards and entrapment risks. 

15. 

Keep children and pets away from this 
bed unless supervised by an adult as 
there is a risk of injury and/or choking 
on small parts. 

16. 

Never stand on the bed. 

17. 

Do not lower the bed while a hoist that 
extends beneath the bed is being 
used. Hoist access is obtained when 
the bed is raised to 45cm measured 
from the floor to the mattress platform 
base. 

18. 

The bed should be left in the floor-level 
position when the patient is 
unattended in order to reduce risk of 
injury due to falls. 

19. 

If using the electronic functions 
adversely affects the health of the 
patient, disconnect the power supply 
and only use the bed in the static 
mode. 

20. 

Do not move the bed when it is in the 
floor-level position. 

21. 

This bed should not be used for 
transporting patients in vehicles. 

22. 

This bed is not recommended for 
users outside of the weight and height 
specifications detailed in Section 5  

23. 

Before operating this bed, ensure the 
patient is safely positioned to reduce 
the risks of bed fall and entrapment. 

24. 

Always check for any entrapment risks 
under the bed before lowering to the 
floor-level position. 

Summary of Contents for EMPRESA NSB-0-FL6-000

































Reviews: