background image

Ricoh StreamPunch Ultra/MP Installation Manual

                                                    2 

1.  Recommendations and Pre-requisites 

 

 

You will need the installation kit provided with the StreamPunch Ultra/MP unit, which can be found in 

the main carton. 

 

Using a jogging unit on the finisher will improve the stack quality for binding purposes.

 

 

2.  Unpacking 

 

 

Inspect the outside of the package for shipping damage. If there is evidence of shipping damage, 

contact the shipping carrier immediately. 

 

Remove the punch from its shipping carton. Three people are recommended, one lifting at the casters 

while two lift at the top cover. DO NOT lift using the front door panel. 

 

Retain the smaller accessory box; it contains parts required for correct installation of the StreamPunch 

Ultra/MP. 

 

Inspect for any concealed damage to the unit. If there is evidence of concealed shipping damage, 

contact the shipping carrier immediately. 

 

Remove all shipping tape from doors and levers. 

 

3.  Configurations 

 

StreamPunch 

Ultra

 can be installed with the below printer/finisher configurations: 

Product 

name 

Project name 

Peripheral 

Pro C5300 

Charis-C3 pro 

SR5110 / SR5120 / SK5040 

Pro C5310 

  

Pro 8300 

Baron-C3 

SR5110 / SR5120 / SK5040 

Pro 8310 

  

Pro 8320 

  

Pro C7200 

Taurus-C3/C3.5 

SR5050 / SR5060 

SR5110 / SR5120 / SK5040 

Pro C7210 

  

Pro C9200 

Andromeda-

P2/P2.5 

  

SR5050 / SR5060 

SR5110 / SR5120 / SK5040 

Pro C9210 

 

StreamPunch 

Ultra MP

 can be installed with the below printer/finisher configurations: 

Product 

name 

Project name 

Peripheral 

MP 6503 

Martini-C6 

SR4080 

MP 7503 

  

MP 9003 

  

IM C6500 

Charis-C3 office 

SR4140 

IM C8000 

  

 

Use communication cable 7718535 

 

 

 

 

 

 

 

 

Use communication cable 7715727 

Summary of Contents for GBC Ricoh StreamPunch Ultra












Reviews: