manualshive.com logo in svg

Access Vanish, Installation Instructions And Owner'S Manual, Page: 8 / 8

Share
Download
Access Vanish Installation Instructions And Owner'S Manual Download Page 8

8

PARTS DIAGRAM

TROUBLESHOOTING

PROBLEM SOLUTION

Cover too loose 

Turn both tension adjusters counter clockwise to move  

 

front bar forward (Refer to #4C, see arrows next to adjuster)

Cover too tight 

Turn both tension adjusters clockwise to move front bar  

 

forward (Refer to #4C, see arrows next to adjuster)

Gap between roll-up bar and tailgate  Rails set too high (Refer to #4B)
Cover is too wide 

Check rails.  Rails in - too wide - push all clamps to top of   

 rail
...too narrow 

Rails out - too narrow - pull all clamps down on rail (Refer  

 

to #1D)

Lopsided cover too much on one side  Check front bar.  It must be centered side to side (Refer to  
 #3D)
Top of  tailgate hits rear bar when  

Raise side rails at rear of  box until tailgate closes without 

attempting to close 

pushing rear bar up (Refer to #4B)

Manual slide locks too loose or  

Use 1/8” allen wrench and adjust set screw tighter or too 

tight 

looser as desired.  Lock performs best with some friction  

 

3/8” x 3/4” bolt 

& nut

(2 per cover)

EZ-Dial left

tension adjuster

3/8” x 1/4” bolt

& washer

(2 per cover)

Front bar

Quick release storage straps

(2 per cover)

Support bows

Slide lock

Rear roll-up 

bar

Right rail

passenger side

Side Lock

Left rail

drivers side

Rail clamps

TONNEAU COVERS

CAR ACCESSORIES

Summary of Contents for Vanish









Reviews:

No comments