manualshive.com logo in svg

Access Vanish, Installation Instructions And Owner'S Manual, Page: 3 / 8

Share
Download
Access Vanish Installation Instructions And Owner'S Manual Download Page 3

3

A. The cover comes pre-rolled to its 
normal open position for ease of  instal-
lation. Set pre-rolled cover on tailgate 
with front bar facing up as shown. Align 
EZ-Dial Tension Adjuster (marked L) 
on driver side of  cover - positioned as 
shown in photo at left. 

2. ASSEMBLING TENSION ADJUSTERS TO COVER

B. Turn 1-1/4” bolt with flat washer 
onto nut in bar. Leave loose for now. 

See 

photo.

 Repeat for EZ-Dial (R) on pas-

senger side of  cover, and leave that bolt 
loose also.

C. Next install a 2nd clamp at midway 
point of  box and rail. Now check rail for 
level. 

See photo at left and illustration below.

 

If  rail tilts up, move clamps down and 
tighten. If  rail tilts down, move clamps 
up and tighten.

1. INSTALLING COVER SIDE RAILS CONT’D.

Second 

clamp

D. Install third clamp as close to tailgate 
as possible. 

See photo.

 Make sure all clamps 

are placed in best up or down position 
for a level rail. Then recheck all clamps 
to insure adequate tightness.

Third clamp last

Nut

“L” Left

EZ-Dial

Working from front to tailgate 

match this point of cover rail 

with top of pickup box as 

clamps are installed

This part of rail 

should be near 

level

Inside lip of box

Adjust clamps 

up or down 

until they 

hold rails 

level when 

tightened

Summary of Contents for Vanish









Reviews:

No comments