background image

13

 

 

7.2

  Faults and treatment 

Item 

Possible reasons 

Fault handling 

Temp. sensor 

failures 

The sensor has not been 

connected correctly 

Check the circuit connectors

and connect it again 

The sensor is 

damaged

 

Change the sensor 

high Temperature 

alarm 

The condenser or evaporator is 

dirty and blocked 

Clean the condenser or evaporator 

Refrigerating capacity isn’t 

enough 

Please consult usability professional 

The temperature setting is fault  Set the temperature again 

Frequent high 

system pressure 

alarm 

The condenser or evaporator is 

dirty and blocked 

Clean the condenser or evaporator 

External fan is fault 

Change the fan 

Condenser temperature sensor 

wrongly sends alarm 

Change the condenser temperature sensor 

Evaporator

-frozen 

alarm 

Internal cycling path is blocked 

Check if there are block to stick the internal 

cycling path 

Internal fan is fault 

Maintain or change it 

Refrigerating system can’t stop 

Check if the air-conditioner reaches the 

refrigeration stop conditions but the actual status 

doesn't stop, if yes, inform the AC maker to deal 

with it. 

Evaporator temperature sensor 

wrongly sends alarm 

Change the evaporator temperature sensor 

Compressor can’t 
run 

There is no cooling demand 

Check if refrigeration is not needed 

Within shutdown delay 

Check if compressor is protected 

Compressor line has not been 

connected correctly 

Check the compressor line

and connect it again 

Compressor protect switch or 

motor is fault   

Check if compressor protect switch is ok, and 

change compressor protect switch if fault; if motor 

is fault, change the compressor 

Internal fan can’t 
run 

Internal fan is fault 

Change the fan 

Internal fan line has not been 

connected correctly 

Check the Internal fan line

and connect it again 

External fan is stuck 

Check if there are block to stick the fan or not, and 

clear the block 

Summary of Contents for MGA0800/A1

















Reviews: