Abus PLBW10100 Manual Download Page 4

 

English 

Notes on handling batteries 

 

Make sure that batteries are not in the hands of children. Children could put batteries in their 
mouths and swallow them. This can cause serious damage to health. In this case, consult a 
doctor immediately! 

 

Normal batteries must not be charged, heated or thrown into an open fire (danger of explosion!) 

 

Do not expose the battery to any heat source or direct sunlight and do not store it in a place with 
a very high temperature. 

 

The battery must not come into contact with water. 

 

The battery must not be disassembled, punctured or damaged. 

 

The battery contacts must not be short-circuited. 

 

Replace weakening batteries in good time. 

 

Always replace all batteries at the same time and use batteries of the same type. Ideally, use 
identical batteries from the same manufacturer as those from the original scope of delivery, as 
the device has been intensively tested with these batteries to ensure optimal function.  

 

Leaking or damaged batteries can cause burns on contact with skin. In this case use suitable 
protective gloves. Clean the battery compartment with a dry cloth. 

 

Cleaning 

 

Dusty equipment must be cleaned. Dust deposits in the air slots can be sucked off or blown out. 
If necessary, the dust can be removed with a brush. 

 

The surface can be cleaned with a cloth slightly moistened with soapy water. Use only suitable 
microfibre cloths for high-gloss surfaces. 

 

Make sure that no water gets inside the device! 

 

Do not clean the appliance in the dishwasher! 

 

Do not use sharp, pointed, abrasive, corrosive cleaning agents or hard brushes! 

 

Do not use chemicals! 

 

Do not clean the device with easily flammable liquids! 

 

Notes on the disposal of the device 

Attention:  The  EU  Directive  2012/19/EU  regulates  the  proper  return,  treatment  and 
recycling  of  used  electronic  equipment.  This  symbol  means  that,  in  the  interest  of 
environmental protection, the device must be disposed of at the end of its service life in 
accordance  with  the  applicable  legal  regulations  and  separately  from  household  or 
commercial  waste.    The  old  device  can  be  disposed  of  at  the  appropriate  official 
collection points in  your country. Observe the local regulations  when disposing  of the 
materials.  For  further  details  about  the  take-back  (also  for  non-EU  countries),  please 

contact your local administration. Separate collection and recycling helps to conserve natural resources 
and ensures that all health and environmental regulations are respected when recycling the product. 

 

 

Summary of Contents for PLBW10100



















Reviews: