background image

 

English 

Introduction 

 

Dear customer, dear customer, 

we are pleased that you have decided to use our product and thank you for your trust! You have made 
a good choice. 

This motion detector (hereinafter referred to as "device") has been developed and manufactured with 
the greatest care. Please read these operating instructions in full and observe all operating and safety 
instructions, as this ensures the best possible handling of the device.  This document is regarded as 
assembly and maintenance instructions. 

 

ABUS  Security-Center  hereby  declares  that  the  enclosed  product  complies  with  the  following 
guidelines concerning the product: 

 

RED  Directive  2014/53/EU,  EMC  Directive  2014/30/EU,  Low  Voltage  Directive  2014/35/EU,  RoHS 
Directive  2011/65/EU.  The  full  text  of  the  EU  Declaration  of  Conformity  is  available  at  the  following 
Internet address 

www.abus.com/product/PLBW10100

 

It can also be obtained from the following address: 

ABUS Security Center GmbH & Co KG, 

Left Kreuthweg 5, 86444 Affing, GERMANY 

 

 

 

 

If you have any questions or suggestions, please contact our customer service: 

Mail:    

 

 

ABUS Support, Linker Kreuthweg 5, 86444 Affing, Germany 

E-mail:  

 

 

[email protected]

 

Phone:  

 

 

+49 8207 959 90 0 

Opening hours hotline:  

Mon-Thu: 08 - 17 h; Fri: 08 - 14 h 

 
 
 
 
 
 
 
All contained company names and product names are trademarks of their respective owners. All rights 
reserved. 

 

 

Disclaimer 

This operating manual has been prepared with the utmost care. Should you nevertheless notice any 
omissions or inaccuracies, please notify us in writing at the address given above. 

Your rights are limited to the repair or replacement of this product in the condition as delivered. ABUS 
Security Center assumes no liability for any special, incidental or consequential damages, including 
but not limited to loss of revenue, loss of profits, restrictions in the use of the software, loss or recovery 
of data, cost of replacement equipment, downtime, property damage and claims by third parties, as 
a result of, among other things, the followinga. contractual, statutory or damage compensation claims 
arising from the warranty, irrespective of other limited warranty provisions or those implied by law or 
in the event that the limited warranty does not apply, the scope of liability of ABUS Security Center is 
limited to the purchase price of the product. 

The contents of this manual may be changed without prior notice. 

© ABUS Security Center GmbH & Co KG, 09/2019 

Summary of Contents for PLBW10100



















Reviews: