ABSCO SHEDS CPSW50 Assembly & Instruction Manual Download Page 14

Page: 14 / 18

STEP 10

IMMEDIATE MAINTENANCE:

BEND THE ENDS OF 16 FLAT STRIPS (270mm X 25mm) AS

SHOWN AND SECURE AT MAXIMUM

1500mm CENTRES WITH ONE

SCREW AT EACH END.

CUT A ROUND HOLE 51mm IN DIAMETER

IN ONE END OF THE REAR EDGE BEAM. THIS

CAN BE DONE BY DRILLING A SERIES OF 3mm HOLES

AND THEN PUNCHING OUT THAT SECTION. FIT THE GALVANISED GUTTER DROP AND SEAL WITH

SILICONE. FASTEN THE DOWNPIPES AND BENDS AS SHOWN. BEND THE 270 x 25 FLAT STRIPS
(DS) TO SHAPE AND FASTEN THE DOWNPIPE TO THE COLUMNS.

CLEAN DOWN ALL ROOF AND EDGE/CROSS BEAM INTERNAL AREAS. METAL FILINGS FROM
DRILLING HOLES AND USING SELF DRILLING SCREWS CAN CAUSE DISCOLORATION AND
CORROSION TO ROOF SHEETS AND GALVANIZED FRAMING SECTIONS.

DP-5

DP-3

DP-2

DP-1

DP-4

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

CARPORT MODEL: CPSW50

10-05-2017

Absco Industries

Skillion Carport Model: CPSW50

PAGE 14

Summary of Contents for CPSW50



















Search results

Summary of Contents for CPSW50

Reviews:

Related manuals for CPSW50

Brands by name

Popular brands

ABSCO SHEDS CPSW50, Assembly & Instruction Manual

Search results

Summary of Contents for CPSW50

Reviews:

Related manuals for CPSW50

Brands by name

Popular brands