ABSCO SHEDS CPSW33 Manual Download

Page: 7 / 18

M10 x 20 BOLT

CROSS/EDGE BEAM

SPLICE PLATE

M10 WASHERS

M10 NUT

STEP 1.

STEP 2.

JA-2

JA-1

EB-3000

EB3000

EBRH-2750

EBLH-2750

EBRH-2750

FRONT OF CARPORT

CB-2720

CB-2850

CB-2720

ALSO FASTEN THE BOTTOM OVERLAP

SECTIONS OF THE EDGE BEAMS WITH
THREE TEK SCREWS.

SECURE THE EDGE BEAMS TOGETHER AT EACH
CORNER USING THE JOINER ANGLES AS SHOWN.

THE JOINER ANGLES SHOULD BE POSITIONED
ON THE INSIDE OF THE EDGE BEAMS, HELD WITH
'G' CLAMPS, AND FASTENED WITH TEK SCREWS

FROM THE OUTSIDE OF THE EDGE BEAMS.

SEAL ALL JOINTS WITH SILICONE.

THE EXTERNAL DIMENSIONS OF THIS FRAME
SHOULD MATCH THE CONCRETE SLAB SIZE OF
3000 x 5500 WITH A DIAGONAL MEASUREMENT
OF 6265, AS SHOWN ON THE FRONT PAGE OF
THIS INSTRUCTION.

JOIN THE EDGE BEAMS AND CROSS

BEAMS TOGETHER WITH THE SPLICE
PLATES, USING M10 x 20 BOLTS,
NUTS AND WASHERS AS SHOWN.

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

CARPORT MODEL: CPSW33-41

10-05-2018

Absco Industries

Skillion Carport Model: CPSW33-41

PAGE 07

Summary of Contents for CPSW33



















Search results

Summary of Contents for CPSW33

Reviews:

Related manuals for CPSW33

Brands by name

Popular brands

ABSCO SHEDS CPSW33, Manual

Search results

Summary of Contents for CPSW33

Reviews:

Related manuals for CPSW33

Brands by name

Popular brands