ABSCO SHEDS 3060HG Page 7 Assembly Instruction Manual Download

Page: 7 / 53

Absco Highlander Shed

Model: 3060HGK

INSTRUCTIONS

AND VIDEOS

COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS

MAIN PACK CARTON (PACK 2 OF 4)

300

HIGH-PORTAL FRAME ACCESSORIES

KNEE PLATE

APEX PLATE

10mm

DYNABOLT

16mm TEK

SCREWS

STEEL SHEET

2034mm X 773mm

H30

STEEL SHEET

2034mm X 773mm

H31

C1482

CHANNEL L = 1482mm

C1954

CHANNEL L = 1954mm

MULTI PURPOSE
BRACKET

C1954

C1482

J=20mm TAB NOTCH ON ONE END ONLY

K=20mm TAB NOTCH ON BOTH ENDS

L=45mm LIP NOTCH ON ONE END ONLY

M=45mm LIP NOTCH ON BOTH ENDS

N=20mm TAB NOTCH + 45mm LIP NOTCH

ON ONE END ONLY

P=20mm TAB NOTCH + 45mm LIP NOTCH

ON BOTH ENDS

R= ONE END: 20mm TAB NOTCH + 45mm LIP NOTCH

OTHER END: 90mm LONG LIP NOTCH

S= SPECIAL NOTCHING NOT NOTED ABOVE.

20mm TAB NOTCH

45mm LIP NOTCH

20mm TAB NOTCH

COMBINED WITH A

45mm LIP NOTCH

(PRE-PUNCHED HOLES

TO ASSIST WITH LOCATING
SELF DRILLING SCREWS)

THESE FOUR DIGITS REPRESENT THE

OVERALL LENGTH OF THE ITEM.

THE FIRST LETTER OF THE PART

NUMBER IS USED TO IDENTIFY

THE NOTCHING TYPE OF THE ITEM.

eg.

2940

K2940 = ONE CHANNEL, 2940mm LONG

WITH A 20mm TAB NOTCH AT EACH END.

PAGE 7

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION - MODEL: 3060HGK 01/07/16

Summary of Contents for 3060HG






















































Search results

Summary of Contents for 3060HG

Reviews:

Related manuals for 3060HG

Brands by name

Popular brands

ABSCO SHEDS 3060HG, Assembly Instruction Manual

Search results

Summary of Contents for 3060HG

Reviews:

Related manuals for 3060HG

Brands by name

Popular brands