Abit SI-2P+ User Manual Download Page 58

Page: 58 / 70

5-2 Chapter

5.1. Setup

Items

•

Intel Chipset Software Utility

Install Intel chipset driver for Windows Operating System.

•

ATI VGA Driver

Install ATI VGA graphic driver for Windows Operating System.

•

Intel LAN Driver

Install the drivers needed to run Fast Ethernet controller. The operating
systems supported are Windows, Windows XP 64-bit, Linux, Netware, and
FreeBSD.

•

Adaptec Ultra320 Driver

Install Adaptec Ultra320 SCSI driver for Windows Operating System.

•

Manual

View the user’s manual in PDF.

•

Utility

Click to enter the sub-screen for installing software like Storage Management,
Award Flash, DirectX8.1, LoFormat, and Utility Acrobat Reader.

•

Hardware Doctor

Install the Hardware Doctor program for monitoring the system health.

•

Browse CD

Browse the contents of this CD-ROM.

•

Exit the CD setup Items Menu.

SI-2P+

Summary of Contents for SI-2P+







































































Search results

Summary of Contents for SI-2P+

Reviews:

Related manuals for SI-2P+

Brands by name

Popular brands

Abit SI-2P+, User Manual

Search results

Summary of Contents for SI-2P+

Reviews:

Related manuals for SI-2P+

Brands by name

Popular brands