Abit SI-2P+ User Manual Download Page 5

Page: 5 / 70

Introduction 1-1

Chapter 1.

Introduction

1.1. Features & Specifications

Processor

•

Supports dual Intel

Xeon 400MHz/533MHz Processors with 512K L2

Cache up to 2.0GHz ~ 2.8GHz and higher

Chipset

•

Intel

E7501 Chipset Memory Controller Hub (MCH)

•

2x 82870P2 64-bit PCI/PCI-X Controller Hub 2 (P64H2)

•

82801CA I/O Controller Hub 3-S (ICH3-S)

Memory

•

6x 184-pin DIMM sockets support 144-bit wide (Dual Channel)
PC2100/PC1600 (DDR266/DDR200) memory

•

Up to 12GB, ECC, Registered memory capacity (Chipkill technology
support)

LAN

•

Intel

82546 dual ports Gigabit Ethernet controller

•

RX and TX IP and TCP/UDP checksum off-loading capabilities

•

Front panel LAN Active/Link LED

Graphics

•

Onboard ATi RAGE XL PCI interface VGA

•

4MB local SDRAM memory support

PCI Extension Slot

•

4x PCI-X, support 64bit one 133MHz and three 100MHz slots

•

1x PCI 32bit/32MHz

Storage

•

Dual Ultra 320 SCSI based on Adaptec 7902 ASIC with optional
Adaptec Zero Channel RAID (ZCR) SO-DIMM interface riser

•

Dual ATA 100 IDE port support up to 4 IDE drives

•

1x Floppy Port

Multi I/O Functions

•

2x Serial Ports / 1x Parallel Port

User’s Manual

Summary of Contents for SI-2P+







































































Search results

Summary of Contents for SI-2P+

Reviews:

Related manuals for SI-2P+

Brands by name

Popular brands

Abit SI-2P+, User Manual

Search results

Summary of Contents for SI-2P+

Reviews:

Related manuals for SI-2P+

Brands by name

Popular brands