Abit SI-2P+ User Manual Download Page 19 | Manualshive

Page: 19 / 70

background image

Hardware Setup

2-9

2.5.2. FAN

Connectors

These 3-pin connectors each provide power to the cooling fans installed in your
system.

The CPU must be kept cool by using a powerful fan with heatsink. The system is
capable of monitoring the speed of the CPU fan.

•

FAN_1:

CPU0 Fan

•

FAN_2:

CPU1 Fan

•

FAN_3/4/5:

System Fan

WARNING:

These fan connectors are not jumpers. DO NOT place jumper caps on

these connectors.

User’s Manual

«
...
17
18
19
20
21
...
»

Summary of Contents for SI-2P+







































































Reviews:

No comments

Related manuals for SI-2P+

Brand: Aaeon Pages: 132

Brand: Aaeon Pages: 50

Brand: Yamaha Pages: 96

Brand: Gigabyte Pages: 74

Brand: Texas Instruments Pages: 23

Brand: NXP Semiconductors Pages: 269

Brand: TYAN Pages: 63

Brand: Texas Instruments Pages: 19

EVAL-IH-R5IPB-A-V1

Brand: Infineon Pages: 34

Brand: ASROCK Pages: 144

Brand: Advantech Pages: 4

Brand: Gigabyte Pages: 20

Brand: Texas Instruments Pages: 13

Brand: SOYO Pages: 91

Brand: Siemens Pages: 2

Brand: Siemens Pages: 8

Brand: Siemens Pages: 18

Brand: Siemens Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands