manualshive.com logo in svg

ABB XIO-00, User Manual

Share
Download
ABB XIO-00 User Manual Download Page 38

38

 | XIO USER MANUAL | 2106424MNAB 

 

 

 

 

4.3

 

Establish local communication 

Connect the laptop to the USB or Ethernet ports to establish initial local communication. These ports are 

configured at the factory for local operator access. Configure PCCU to use any of these ports.  

–

 

To use USB, see section 

4.3.1 Using the USB port

 

–

 

To use Ethernet, see section 

4.3.2 Using the Ethernet ports

 

 

IMPORTANT NOTE:

 External weatherproof local communication connectors (USB or Ethernet) are 

available on 

X

CORE enclosures, if purchased. Use external ports to connect locally if the XIO is 

inside an enclosure. If the XIO is a standalone device, use the USB or Ethernet ports.  
Do not use external enclosure connectors for permanent field connections. These connectors are 

only for local access during configuration or maintenance. 

4.3.1

 

Using the USB port 

The following instructions apply to USB port connections. 

Table 4-1: USB cabling

 provides cabling details 

to connect to the USB port. 

Table 4-1: USB cabling 

Host system 

interface type 

Required cabling termination (connectors) or 

adaptors 

ABB part number 

USB 2.0 Type A 

receptacle 

USB 2.0 Type mini-B plug to USB 2.0 Type A plug cable 

(referred as USB PCCU32 cable) 

1801800-xxx 

To set up communication using the USB port: 

 

 

 

 

Summary of Contents for XIO-00
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands