background image

Assembly Instructions / TPL65-A ... TPL77-A, TPL65VA

4  Installing the turbocharger / 4.1  Steps for fastening the turbochar-
ger

© Copyright 2020 ABB. All rights reserved.

HZTL455311P0017_EN

Rev.A

July 2020

4

Installing the turbocharger

u

Remove the cover from the oil connection.

u

Inspect the lifting gear.

u

Attach one lifting gear each to the two ribs of the bearing casing provided for this pur-
pose.

 CAUTION

Oil orifices

There is an orifice for adjusting the oil pressure in each of the two oil supply
pipes of the bearing casing. When the cartridge group, the bearing casing or
the turbocharger-is being fitted to the engine, it must be ensured that the
orifices specified for the turbocharger are installed in both oil supply pipes.

u

Check that the oil orifices have been correctly installed.

u

Adjust the turbocharger on the engine.

u

Tighten the fixing screws (

Steps for fastening the turbocharger 

10

).

4.1

Steps for fastening the turbocharger

General information

Subject

Requirement / Information

Turbocharger fixing elements

ISO strength class 10.9 or 12.9

Washers

Hardened, thickness 

 15 % nominal thread

diameter

Dimension a

Height of turbocharger foot

Dimension b

Hole in bracket

Dimension c

Thread length 

 1.5 times the nominal thread

diameter

Coefficient of friction

0.12 (lightly oiled)

Table 5

u

Tighten the foot fixing screws or nuts as per the selected tightening procedure in a Z con-
figuration.

Page 

10

 / 

17

Summary of Contents for Turbocharger TPL-A Series





















Reviews: