background image

Assembly Instructions / TPL85-B14/B15/B16, TPL91-B

1  Introduction / 1.5  Definition of mandatory signs

© Copyright 2020 ABB. All rights reserved.

HZTL455311P0020_EN

Rev.A

July 2020

1.5

Definition of mandatory signs

To be worn at all times

Protective clothing

Safety footwear

 to protect

against mechanical hazard
and risk of falling

Table 1

To be worn according to the specific work

Safety glasses

Safety goggles

Safety gloves

 against

- Mechanical hazard
- Chemical hazard
- Thermal hazard

Respiratory mask

 against

- Dusts
- Gases

Safety helmet

Ear protection

Table 2

1.6

Definition of pictograms

The following pictograms can occur in this document. These point out actions that must be
taken in accordance with the meaning of the relevant pictogram.

Pictogram Meaning

Pictogram Meaning

Tighten with specified torque

Oil free, grease free and dry

Tighten over specified tightening
angle

Affix

Hand-tight, tighten without tools

Measure

Oil

Note

Apply screw locking paste (e.g.
Loctite)

Visually inspect

Apply high-temperature grease

See document

Apply other paste in accordance
with specifications

Dispose of in an environmentally
compatible, professional way
and in compliance with locally
applicable regulations.

Table 3: Pictograms

Page 

4

 / 

17

Summary of Contents for TPL85-B14





















Reviews: