manualshive.com logo in svg

ABB Terra DC Wallbox C UL, Installation Manual, Page: 23 / 38

Share
Download
Page 23
ABB Terra DC Wallbox C UL Installation Manual Download Page 23

 

TERRA DC WALLBOX UL 

2020-10-05 

 

23/38 

5.3

 

Move cabinet to position 

5.3.1

 

Options 

A properly rated lifting devices should be used to move the Terra DC Wallbox from the delivery truck to 
the installation location.  

 

 

DANGER 
Hazardous voltage 
Ensure the product’s power supply group main switch is set to the 
OFF position. Perform a voltage check to verify there is no electrical 
power on the cables or on the system. Secure the product from re-
setting. 

 

 

NOTICE 
Warranty 
Damage due to moving the cabinet to its position is not considered 
a warranty issue. 

5.4

 

Mounting the Terra DC Wallbox  

Preconditions: 

•

 

Tools: Spanner/Wrench size 17. 

•

 

Guide the power cable through the central cable gland, and the Ethernet cable if required, 
through the smaller gland. Install the power wiring in the conduit/raceway that is connected to 
the unit.  See below image for a typical conduit install make ready for installation of the Terra 
DC Wallbox. 

 

5.4.1

 

Mounting the Terra DC Wallbox  

 

NOTICE 
 
A minimum of two people are required to lift a Terra DC Wallbox 
during installation. In general, local regulations should be followed 
as the maximum weight to be lifted may vary. 

 

1.

 

Carefully lower the Terra DC Wallbox onto its location. 

Summary of Contents for Terra DC Wallbox C UL







































Reviews:

No comments