manualshive.com logo in svg

ABB SPA-ZC 302, Installation And Commissioning Manual

Share
Download
ABB SPA-ZC 302 Installation And Commissioning Manual Download Page 63

1MRS755014

SPA-ZC 302

63

Profibus-DPV1/SPA Gateway

Installation and Commissioning Manual

Fig. 8.3.1.-2

SPA LED indicators

See Table 8.3.1-2 for the description of the Profibus LED indicators pictured in 
Fig. 8.3.1.-2 .

8.4.

Troubleshooting

When troubleshooting the gateway, first check the LED indicators described in 
Section 8.3. Self-diagnosis. If there is a LED flashing, a coarse error can be located 
through the flashing pattern of the LED.

8.4.1.

Gateway diagnostics

Detailed information about the error may be available in the diagnostics that can be 
uploaded from the gateway. For details about uploading, see Section 5.4.2.3. Upload 
diagnostics.

SPA

STATUS

SPA

RS485
RS232

TTL

1

2

SPA_LED_a

Table 8.3.1-2

SPA LED indicator description

LED no Description

Colour State

Indicates

Off

No power to the gateway.

Green

Flashing 1 Hz

Power ON. Running in configuration mode.

1

Module Status

On

Power ON. Running in application mode.

Red

Flashing 1 Hz

Configuration error. Test of the onboard configuration file failed 
(gateway not operational).

On

Hardware error (Flash, SRAM, ABS).

Off

SPA/Cfg Communication Idle.

Green

Flashing irregular

Serial Message Transmission when in Application mode (Until SPA 
goes on-line) and when in configuration mode.

SPA

On

SPA Network on-line.

2

Communication

Flashing irregular

Serial message reception error when in both application and 
configuration mode

Status

Red

(framing, parity, CRC error etc.).

On

No SPA slave attached or cabling problem (SPA Network Offline).

Summary of Contents for SPA-ZC 302





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands