manualshive.com logo in svg

ABB SPA-ZC 302, Installation And Commissioning Manual

Share
Download
ABB SPA-ZC 302 Installation And Commissioning Manual Download Page 41

1MRS755014

SPA-ZC 302

41

Profibus-DPV1/SPA Gateway

Installation and Commissioning Manual

5.4.7.2.

Profibus configuration

In the Profibus Configuration field in the main window, see Fig. 5.3.-1 number 5, 
you can modify the following options:

SPA Com Retry 
Count

In this text field, you can define how many times the gateway will 
retry sending a message when failing to get a valid response before 
continuing with the next message. Valid values are 1-32 times. 
The default value is 2.

Global Poll 
Interval

In this field, you can define the idle time of event based updating 
of digital inputs. If the SPA events are present in the SPA slave, 
then they are automatically polled with 100 ms interval until the 
SPA slave has not got anymore events. After this, the gateway 
checks the SPA slave event buffer with the time interval specified 
in this parameter. Default value is 3000 ms.

Global Event 
Poll

By selecting the check box, you can enable polling of SPA 
Events.The events will be stored into the Event buffer. When 
disabled, the polling of events will not be performed at all. Event 
functionality is used by some standard configurations for updating 
the state values. For details, see Section 6.3. Usage and purpose of 
SPA protocol events.

Time 
Synchronization 
Support 

By selecting the check box, you can enable the synchronization of 
the SPA slave device. If it is enabled, it will be necessary to 
provide the gateway with the correct time. If the time 
synchronization is disabled, the gateway will not synchronize the 
SPA slave devices attached to the gateway. 

This function requires a Profibus DP version 1 master which is 
capable of index/slot addressing of acyclic messages.

Date 
Synchronization 
support

By selecting the check box, you can enable the synchronization of 
the SPA slave device. If it is enabled, it will be necessary to 
provide the gateway with the correct date. If the Date 
synchronization is disabled the gateway will not synchronize the 
SPA slave device attached to the gateway.

This function requires a Profibus DP version 1 master which is 
capable of index/slot addressing of acyclic messages.

Default 
Profibus

 Adr.

In this text field, you can configure the default Profibus Node 
Address of the gateway. Valid node addresses are 1-126 for the 
Profibus DP Version 1 module. A value between 100-126 is 
recommended. Default address is 125.

Decimal Place In this text field, you can set how many decimals shall be used 

when the value is passed to Profibus DP. Valid values are 0-6. 
Default value is 2. (Since the SPA slave devices can use 10 integer 
digits and 10 decimal digits, there will be a loss of precision when 
using too many decimals digits together with integer digits.) For 
details, see Section Section 5.4.8.7. Scaling of messages.

Summary of Contents for SPA-ZC 302





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands