background image

Activating Reset of LDCM counters sets the counter concerned to zero. A reset can
be performed by affirmation in the dialog box. This is done by pressing the E key
when YES is highlighted.

13.1.1.6 

Function for energy calculation and demand handling ETPMMTR

Main menuReset/Reset counters/ThreePhEnergMeas(MMTR)/ETP

Resetting accumulated energy values and the maximum demand values.

13.1.2 

Reset disturbances and event list DRPRDRE

Disturbances are reset under Reset menu in the HMI tree.

Main menu/Reset/Reset disturbances

The internal event list is reset under Reset menu in HMI tree.

Main menu/Reset/Reset internal eventlist

13.1.3 

Reset LEDs

13.1.3.1 

Start and trip LEDs

By activating this reset, the colored LEDs above the LCD, if they are latched, will
be reset.

Main menu/Reset/Reset LEDs/Start and trip LEDs

In the dialog box that appears, choose YES to reset.

13.1.3.2 

All indication LEDs

Activating the Reset of indication LEDs will zero all fifteen LEDs to the right of
the LCD.

Main mnenu/Reset/Reset LEDs/All indication LEDs

In the dialog box that appears, choose YES to reset.

13.1.4 

Reset lockout SMPPTRC

Objects that are considered at risk after a trip may be prevented from reconnecting
by a lockout condition. The reset lockout facility is used to undo a lockout
condition caused by a such a trip.

Main menu/Reset/Reset lockout/TripLogic(PTRC,94)/TRP

In the dialog box that appears, choose YES to reset.

Section 13

1MRK 502 014-UEN C

Reset

86

Operator's manual

Summary of Contents for Relion REG670













































































































Reviews: