ABB ProcessMaster Commissioning Instruction Download Page 69 | Manualshive

Page: 69 / 80

background image

Extended

diagnostic

functions

CI/FEX300/FEX500-EN

FEX300, FEX500

EN - 67

8 Extended

diagnostic

functions

8.1

General remarks

Important (Note)

• The extended diagnostic functions are available for ProcessMaster 500 and

HygienicMaster 500 only.

• The "Partial Filling Detector" function is

not

available for HygienicMaster 500.

• When using the extended diagnostic functions the external flowmeter sensor must not be

provided with a preamplifier.

• To facilitate initial start-up, the extended diagnostic functions are deactivated (factory

default).

• To use the extended diagnostic functions, a "start-up fingerprint" must be created during

start-up of the flowmeter.

• Each diagnostic function (e.g. Gas Bubble Detector or Electrode Deposit Detector) can be

individually activated. Once activated, the diagnostic function must be calibrated according
to the conditions on site and the limit values must be set.

8.1.1 Detection of partial filling

Optionally, a measuring electrode (TFE electrode) is available for detecting a partially filled
flowmeter sensor. The alarm for partial filling is output via the programmable digital output.

Conditions for using the function:

•  Nominal diameter from DN 50 (2“)
•  Max. signal cable length for version with external transmitter 200 m (656 ft).
•  Conductivity of the fluid: 20

μ

S/cm ... 20,000

μ

S/cm

• The function is only available for ProcessMaster 300 / 500 without explosion protection or

with explosion protection for Zone 2 / Div 2.

Additional installation conditions:

• The flowmeter sensor must be installed horizontally with the terminal box pointing upward.

8.1.2 Detection of gas bubbles

Gas bubbles in the fluid are detected by using an adjustable maximum limit value. When this
limit value is exceeded, an alarm is tripped via the programmable digital output, depending on
the configuration.

Conditions for using the function:

• This function is available in the nominal diameter range

1)

of DN 10 … 300 (3/8 “ ... 12 “).

• The signal cable length of the external transmitter must not exceed a maximum value of

50 m (164 ft) .

• For this function, the conductivity of the fluid must be in the range

20

μ

S/cm ... 20,000

μ

S/cm.

Additional installation conditions:

• The flowmeter sensor can be installed either horizontally or vertically. Vertical installation is

preferred.

1) The specified nominal diameter range is valid for ProcessMaster, only. The nominal diameter range valid for

HygienicMaster is DN 10 … 100 (3/8 “ ... 4 “).

«
...
67
68
69
70
71
...
»

Summary of Contents for ProcessMaster

















































































Reviews:

No comments

Related manuals for ProcessMaster

Brand: Keithley Pages: 48

Brand: Yamaha Pages: 3

Brand: Oceanic Pages: 17

Brand: DAKOTA ULTRASONICS Pages: 25

Brand: DAKOTA ULTRASONICS Pages: 36

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Tascam Pages: 4

Brand: Harpers Pages: 8

Brand: YOKOGAWA Pages: 16

Brand: LEGRAND Pages: 5

Digital Piano CA750

Brand: Kawai Pages: 76

Brand: H. HERMANN EHLERS Pages: 40

Brand: Kawai Pages: 72

Brand: Clavia Pages: 13

Brand: Suaoki Pages: 79

Brand: wtw Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands