manualshive.com logo in svg

ABB PowerValue 11T IN, User Manual

Share
Download
ABB PowerValue 11T IN User Manual Download Page 22

22

POWERVALUE 11T IN — 

6-10 KVA

4.6 LCD settings

WARNING!

Changing ups settings might adversely impact the load supply or load functionality.  
It is recommended to disconnect the load before proceeding.

Press and hold select button for 5 seconds to enter UPS settings mode when UPS is in standby mode or 
bypass mode. Press and hold "Off/Enter" and "select" buttons for 5 seconds to switch LCD screen in 
rack or tower display.

There are three parameters to set up the UPS. Refer to following diagram.
Parameter 1: It’s for program alternatives. Refer to below table for the programs to set up.
Parameter 2 and parameter 3 are the setting options or values for each program.

Note: 

Please select 

“Up” 

or 

“Down”

 button to change the programs or parameters.

01: Output voltage

Interface

Settings

Parameter 3: Output voltage

You may choose the following output voltage in parameter 3:

208:

 Presents output voltage is 208Vac

220: 

Presents output voltage is 220Vac

230:

 Presents output voltage is 230Vac

240:

 Presents output voltage is 240Vac

02: Output frequency

Interface

Settings

Parameter 2: Output frequency

Setting the output frequency. You may choose following three options in parameter 2:

50.0Hz:

 The output frequency is setting for 50.0Hz.

60.0Hz: 

The output frequency is setting for 60.0Hz.

ATO:

 If selected, output frequency will be decided according to the latest normal utility 

frequency. If it is from 46Hz to 54Hz, the output frequency will be 50.0Hz. If it is from 56Hz to 

64Hz, the output frequency will be 60.0Hz. ATO is default setting.

Parameter 3: Frequency mode

Setting output frequency at CVCF mode or non-CVCF mode. You may choose following two 

options in parameter 3:

CF:

 Setting UPS to CVCF mode. If selected, the output frequency will be fixed at 50Hz or 60Hz 

according to setting in parameter 2. The input frequency could be from 46Hz to 64Hz.

NCF:

 Setting UPS to normal mode (non-CVCF mode). If selected, the output frequency will 

synchronize with the input frequency within 46~54 Hz at 50Hz or within 56~64 Hz at 60Hz 

according to setting in parameter 2. If 50 Hz selected in parameter 2, UPS will transfer to 

battery mode when input frequency is not within 46~54 Hz. If 60Hz selected in parameter 2, 

UPS will transfer to battery mode when input frequency is not within 56~64 Hz.

*If Parameter 2 is ATO, the Parameter 3 will show the current frequency.

Summary of Contents for PowerValue 11T IN































Reviews:

No comments

Brands by name

Popular brands

Load more brands