ABB MegaFlex UL S1 Series User Manual Download Page 45

Page: 45 / 86

45/86

MegaFlex 1000 to 1600

UPS User Manual / REV-A

Commands 1 screen

Allows the user to execute UPS operation
commands.

Rectifier

Rectifier ON

Rectifier switching ON command.

Rectifier RESET

Rectifier restore command.
Reserved for the ABB Service Center.

Led Rectifier status

Indicates the Rectifier’s status: ON = lit

OFF = turned Off

Inverter

Inverter ON

Inverter switching ON command.

Note!
When eBoost™ Operation Mode is enabled, control of Inverter status and selection of the feed

path is done autonomously by the UPS control logic.
Therefore, Inverter ON / Inverter OFF commands are disabled when eBoost™ Operation Mode is
enabled.

Inverter OFF

Inverter switching OFF command.

This command is also used as EPO (Emergency Power Off) reset after the contact closing.

Note!
Inverter OFF command is disabled when eBoost™ Operation Mode is enabled.

Led Inverter status

It indicates the Inverter status:
ON / OFF / Pre-charge / Pre-charge completed / Soft-start.

Summary of Contents for MegaFlex UL S1 Series























































































Search results

Summary of Contents for MegaFlex UL S1 Series

Reviews:

Related manuals for MegaFlex UL S1 Series

Brands by name

Popular brands

ABB MegaFlex UL S1 Series, User Manual

Search results

Summary of Contents for MegaFlex UL S1 Series

Reviews:

Related manuals for MegaFlex UL S1 Series

Brands by name

Popular brands