ABB MegaFlex UL S1 Series User Manual Download Page 40

Page: 40 / 86

40/86

MegaFlex 1000 to 1600

UPS User Manual / REV-A

6.4

Setup

SETUP

The SETUP mode is entered any time the
“

SETUP

” key is pressed.

This screen allows the user to modify some
parameters permitting to adapt some
functions of the UPS to his/her needs,
described as follows.

The LCD will display a series of screens
containing the user parameters, accessible
without password protection.

In this mode the keys perform the following functions:

Shows the main screen MEASURES.
See Section 6.2.

Shows the main screen EVENTS.
See Section 6.3.

Return to HOME screen.

Shows the main screen COMMANDS.
See Section 6.5.

Shows the operating status of the RPA PARALLEL SYSTEM.
See Section 6.6.

Key to reset general alarm and buzzer.

Shows the screen User.

Shows the screen Service Full.
Reserved for the ABB Service Center, at this level the parameters access is protected by a
“Service Code”.

Summary of Contents for MegaFlex UL S1 Series























































































Search results

Summary of Contents for MegaFlex UL S1 Series

Reviews:

Related manuals for MegaFlex UL S1 Series

Brands by name

Popular brands

ABB MegaFlex UL S1 Series, User Manual

Search results

Summary of Contents for MegaFlex UL S1 Series

Reviews:

Related manuals for MegaFlex UL S1 Series

Brands by name

Popular brands