background image

Exchange of position sensor

43/68-13 EN

Electrical Linear Actuators for Continuous Modulating Control LME620AI / LME620AN (Contrac) 

19

7

Exchange of position sensor

7.1

Dismounting

- drive actuator into 50% position
- delete the current position settings by pressing the drive buttons 

on the LCP for at least 5

sec.

- switch-off the voltage supply
- disconnect the main plug
- undo the four fastening screws (1) of the pin strip carrier and push the carrier aside
- undo the two fastening screws (2) of the position sensor, pull the sensor out of the gears 
- disconnect the plug of the signal cable on the sensor pcb

7.2

Mounting

The toothed gear pair of the position sensor is held in place by a tension spring (3), to ensure a back-
lash-free contact when the direction of rotation is reversed

- set the stop pin to the center position, as seen in figure 23
- align the sensor and its gears with the actuator; set the first toothed gear in approx. 12:00 o’clock

position (see fig. 24) onto the drive shaft gear (4) 

- slightly move the sensor back and forth to pre-tension the toothed gears until the second toothed

gear snaps in

- fasten the screws (2) tightly.

Finally provide a new basic setting of the actuator operating range. See the Set Up chapter in the ac-
tuator and / or electronic unit manual for details. 

Fig. 23: Position sensor

Fig. 24: Mounting position

and 

(d0181rxa)

3

(68d_0048)

2

1

Summary of Contents for LME620-AI































Reviews: