ABB Emax 2 Retrofill Installation And Maintenance Manual Download | Manualshive

Page: 6 / 77

background image

6 - Related Publications

7 - Service and Support

8 - Estimated Time to Complete Tasks

Service and support are available from ABB Inc USA.

Email: [email protected]
Phone: 888-385-1221

Verify the secondary disconnects and match the switchgear cublicle which may take up to
1Hr depending on the complexity of the original breaker. Once the retrofill breaker is fully
prepared, it should take about 20 minutes to swap out the old breaker and rack in the new
Emax 2 Retrofill circuit breaker if the proper lifting bar and hoist are available, it may take an
additional 30 min to replace the door.

The Emax 2 Retrofill, when ordered with 4 wire ground fault, will be equipped with a Neutral
CT adapter. The adapter will modify the GE MicroVersaTrip type Neutral CT output to a
Rogowski sensor output compatible with the Emax 2 Retrofill Trip Unit. With this device, it
will not be necessary to change the neutral CT in the switchgear to a Rogowski sensor.

Title

Publication

Publication Number

Accessory: Neutral CT Adapters Installation Instructions
Accessory: Programmer Disconnects Installation Instructions
Accessory: Primary Disconnects Installation Instructions
Accessory: Secondary Disconnects, Installation Instructions
E2.2, 4.2, 6.2 Breakers Installation, Operation & Maintenance Manual
Instructions for using Ekip touch protection releases & accessories
Emax 2 Family Trip units Engineering manual

Installation Manual AKD 10

Installation Manual AKD 8

Installation Manual AKD 6

Installation Manual AKD 5

Accessory: Door Interlock (Door Interlock Kit)

Accessory: Kirk Key installation Manual

Accessory Retrofill Direct Replacement / CiC Full Door Kits AKD-5, 6, 8 & 10

Accessory Retrofill Direct Replacement / CiC Door AdaptorsKits AKD-5, 6, 8 &10

Accessory OEM Direct Replacement Adaptor kits AKD8 & 10

Accessory OEM Direct Replacement Adaptor kits, AKD8 &10, AKR 75/100, B&F TYPE

Accessory OEM Direct Replacement Adaptor kits, AKD8 &10, only for AKR30S

Accessory: Position Switch Plate, Assembly & Wiring

Accessory: Neutral CT Adapters Installation Instructions

Accessory: Programmer Disconnects Installation Instructions

Accessory: Primary Disconnects Installation Instructions

Accessory: Secondary Disconnects, Installation Instructions

E2.2, 4.2, 6.2 Breakers Installation, Operation & Maintenance Manual

Instructions for using Ekip touch protection releases & accessories

Emax 2 Family Trip units Engineering manual

2TSA451010P0000

2TSA451009P0000

2TSA451014P0000

2TSA451011P0000

2TSA451017P0000

2TSA451013P0000

2TSA451007P0000

2TSA451008P0000

2TSA431967R1000

2TSA431968R1000

2TSA431996R1000

2TSA451019P0000

2TSA451018P0000

2TSA451012P0000

2TSA451015P0000

2TSA451016P0000

1SDH001000R0002

1SDH001316R0002

1SDH001330R0002

C

«
...
4
5
6
7
8
...
»

Summary of Contents for Emax 2 Retrofill














































































Reviews:

No comments

Related manuals for Emax 2 Retrofill

Brand: Moeller Pages: 2

Brand: Moeller Pages: 3

Brand: Moeller Pages: 42

DFS 6 A EV OCP Series

Brand: Doepke Pages: 2

Brand: Power Probe Pages: 22

Brand: IDEAL Pages: 4

ETIBREAK NBS 100

Brand: ETI Pages: 2

Brand: Siemens Pages: 12

Brand: Siemens Pages: 2

Brand: Siemens Pages: 3

Brand: Siemens Pages: 3

Brand: Siemens Pages: 5

3VM12 - ED Series

Brand: Siemens Pages: 7

Brand: Siemens Pages: 4

3AH35-SE Series

Brand: Siemens Pages: 48

Brand: ABB Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands