manualshive.com logo in svg

ABB CDPI-01, User Manual

Share
Download
ABB CDPI-01 User Manual Download Page 21

CDPI-01 communication adapter module   21

Diagnostics

„

Faults and warning messages

For the fault and warning messages concerning the 

communication adapter module, see the drive manual.

„

LEDs

The communication adapter module has two diagnostic LEDs.

Technical data

„

CDPI-01 communication adapter module

Name

Color

Description

POWER

Green

Drive control unit is powered.

FAULT

Red

There is an active fault in the drive control unit. 

Degree of protection

IP21 when installed

Ambient conditions

See the drive technical data.

Package

Cardboard

Switches

• Termination switch (S100)
• Bias switch (S101)

Connectors

• Unshielded female connector to the drive 

control unit (X100,  RJ-45)

• Shielded female connector for connecting a 

control panel or a PC (X101, RJ-45)

• Shielded female connector for chaining a 

panel bus (X102, RJ-45)

Power supply

Supplied by the drive control unit

General

• Complies with EMC standard EN 61800-

3:2004

• Printed circuit board conformal coated
• Printed circuit board materials RoHS 

compliant and UL Recognized

Summary of Contents for CDPI-01

























Reviews:

No comments

Brands by name

Popular brands

Load more brands