8
Electrical equipment should only be installed, accessed, ser-
viced and maintained by qualified electrical personnel.
E
Warning –
For safety reasons it is recommended that the
equipment is installed in a way that makes it impossible to
reach or touch the terminal blocks by accident.
The best way to make a safe installation is to install the unit in
an enclosure. Further, access to the equipment should be lim-
ited through use of lock and key, controlled by qualified electri-
cal personnel.
W
Warning –
The meters must always be protected by fuses on
the incoming side.
In order to allow for maintenance of transformer rated meters,
it is recommended that there should be a short circuiting device
installed near the meter.
Do not operate the equipment outside the specified technical
data.
Installation Requirements
To comply with the protection requirements the meter must be
mounted in protection class IP 51 enclosures, or better, according to
IEC 60259.
Meters with wireless communication should not be installed closer
than 20 cm from people.
Troubleshooting
If any of the following icons
W VC
appear in the display after the
installation has been completed and power has been connected to the
meter, refer to the B23/B24 User Manual for detailed information.
B23_B24_install.book Page 8 Thursday, May 30, 2013 4:01 PM
Summary of Contents for B23
