background image

2 Safety

 

Endura AZ20 oxygen monitor | Pumped reference air unit |

INF09/027 Rev. D

3

2.7 Safety recommendations

For safe operation, it is imperative that these service instructions be

read before use and that the safety recommendations mentioned

herein be scrupulously respected. If danger warnings are not

heeded to, serious material or bodily injury could occur.

2.8 Service and repairs

Other than the serviceable items listed in this document, none of the

pump’s components can be serviced by the user. Only personnel

from ABB or its approved representative(s) is (are) authorized to

attempt repairs to the system and only components formally

approved by the manufacturer should be used. Any attempt at

repairing the pump in contravention of these principles could cause

damage to the pump and corporal injury to the person carrying out

the repair. It renders the warranty null and void and could

compromise the correct working of the pump and the electrical

integrity or the CE compliance of the pump. 

If you have any problems with installation, starting, or using the

pump please contact the company that sold it to you. If this is not

possible, or if the results of this approach are not satisfactory,

please contact the manufacturer's Customer Service

2.9 Potential safety hazards 

The following potential safety hazards are associated with operating

the system: 

Electrical (line voltage) 

Warning.

The installation of the pump should be performed

exclusively by personnel specialized and authorized to work on

electrical installations, in accordance with relevant local

regulations. 

Caution.

This equipment has been tested and found to

comply with the limits for Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user is required to correct the interference at his own expense.

Summary of Contents for AZ200 770









Reviews: