background image

Fault tracing   43

6

Fault tracing

About this chapter

This chapter lists all the warning and fault messages including possible causes and 
corrective actions for the Centrifuge Decanter drive.

For the complete list of warning and fault messages, see 

ACS880 primary control program 

firmware manual (3AUA0000085967[English])

.

Warning messages

Note:

 The list also contains events that appear in the Event log.

Code 
(hex)

Warning

Cause

What to do

E200

Pre wash time 
too long

Pre wash speed is higher 
than fill speed.

Decrease pre wash time or 
prewash speed.
See parameters, 

77.04

 

Prewashing speed

 and 

77.10

 

Prewashing time

.

E201

Wash time too 
long

Wash speed is higher than 
spin speed.

Decrease wash time or wash 
speed.
See parameters 

77.05

 

Washing 

speed

 an

77.11

 

Washing time

.

E202

Speed feedback 
not inside range

Actual speed is beyond the 
minimum and maximum 
speed limits.

Increase the deceleration time 
from spinning speed to unloading 
speed or the deceleration time 
from unload speed to stop at zero 
speed.
See parameters 

77.08

 

Dec time 

to unload speed

 an

77.09

 

Dec 

time to zero speed

.

Summary of Contents for ACS880 Series



















































Reviews: