154 The Safe torque off function
STO abbreviations
Abbreviation Reference
Description
Cat.
EN ISO 13849-1
Classification of the safety-related parts of a control
system in respect of their resistance to faults and their
subsequent behavior in the fault condition, and which is
achieved by the structural arrangement of the parts, fault
detection and/or by their reliability. The categories are: B,
1, 2, 3 and 4.
CCF
EN ISO 13849-1
Common cause failure (%)
DC
EN ISO 13849-1
Diagnostic coverage
FIT
IEC 61508
Failure in time: 1E-9 hours
HFT
IEC 61508
Hardware fault tolerance
MTTF
d
EN ISO 13849-1
Mean time to dangerous failure: (The total number of life
units) / (the number of dangerous, undetected failures)
during a particular measurement interval under stated
conditions
PFD
IEC 61508
Probability of failure on demand
PFH
D
IEC 61508
Probability of dangerous failures per hour
PL
EN ISO 13849-1
Performance level. Levels a…e correspond to SIL
SC
IEC 61508
Systematic capability
SFF
IEC 61508
Safe failure fraction (%)
SIL
IEC 61508
Safety integrity level (1…3)
SILCL
IEC/EN 62061
Maximum SIL (level 1…3) that can be claimed for a safety
function or subsystem
SS1
IEC/EN 61800-5-2 Safe stop 1
STO
IEC/EN 61800-5-2 Safe torque off
T1
IEC 61508
Proof test interval. T1 is a parameter used to define the
probabilistic failure rate (PFH or PFD) for the safety
function or subsystem. Performing a proof test at a
maximum interval of T1 is required to keep the SIL
capability valid. The same interval must be followed to
keep the PL capability (EN ISO 13849) valid. Note that
any T1 values given cannot be regarded as a guarantee
or warranty.
See also section
(page
).
Summary of Contents for ACS880-M04
