Technical data
138
UL marking
The drive is cULus listed.
UL checklist
• The drive is to be used in a heated, indoor controlled environment. The drive must
be installed in clean air according to enclosure classification. Cooling air must be
clean, free from corrosive materials and electrically conductive dust. See page
• The maximum ambient air temperature is 40 °C (104 °F) at rated current. The
current is derated for +40…55 °C (+104…131 °F).
• The drive is suitable for use in a circuit capable of delivering not more than
100,000 rms symmetrical amperes, 500 V maximum when the input cable is
protected with T-class fuses. The ampere rating is based on tests done according
to UL 508A.
• The cables located within the motor circuit must be rated for at least
75 °C (167 °F) in UL-compliant installations.
• The input cable must be protected with fuses. Circuit breakers must not be used
without fuses in the USA. For suitable circuit breakers, contact your local ABB
representative. Suitable IEC (class aR) fuses and UL (class J) fuses for drive
protection are listed on page
.
• For installation in Canada, branch circuit protection must be provided in
accordance with the Canadian Electrical Code and any applicable provincial
codes. To fulfil this requirement, use the UL classified fuses.
• For installation in the United States, branch circuit protection must be provided in
accordance with the National Electrical Code (NEC) and any applicable local
codes. To fulfill this requirement, use the UL classified fuses.
• The drive provides overload protection in accordance with the National Electrical
Code (NEC).
CSA marking
CSA marking is pending for the drive.
“C-tick” marking
A “C-tick” mark is attached to each drive in order to verify compliance with the EMC
product standard (EN 61800-3:2004), required under the Trans-Tasman
Electromagnetic Compatibility Scheme for levels 1, 2 and 3 in Australia and New
Zealand.
For fulfilling the requirements of the standard, see section
.
GOST R certificate of conformity
The drive has been given a GOST R certificate of conformity. Available on request.
Summary of Contents for ACS850-04 series
