background image

14

ACS550-CC Packaged Drive with Bypass

Installation

       Terminal Block 1TB

Connection Points

Basic control connections are made to 1TB, which is a din-rail terminal block on the 

back panel at the bottom of the enclosure. 1TB includes screw clamp terminals rated 

for #22-10 AWG stranded or solid wire. Recommended tightening torque is 4.4 - 7.1 

in-lbs.
Terminals 1TB:7 and 1TB:8 are 120 VAC control circuit terminals connected to 120 

VAC control power supplied by the control circuit transformer provided. Terminals 

1TB:9 and 1TB:10 are powered at 24VDC to accept an external contact closure to 

start the drive. Terminals 1TB:13 and 1TB:14 are connected to un-powered relay 

contacts provided for use with externally powered customer control circuits.

Additional Connections

The low voltage speed reference signal input, analog outputs, additional relay 

outputs, and additional digital input connections are available on Terminal Block X1 

inside the ACS550. Note that the Bypass control circuitry uses inputs and outputs 

DI1,DI4 and R02. These inputs are not available for any other purpose and must not 

be reconfigured. Output RO2 is wired to the terminal block, 1TB. AI1, AI2, DI3, DI5, 

DI6, RO1, and R03 are available for use. Refer to the 

ACS550-01/U1 User’s Manual 

for information about control connections on Terminal Block X1. When making 

connections to Terminal Block X1, be careful not to disturb the factory installed 

wiring between X1 and the Bypass control circuitry.

Analog Input

The external “Auto” speed reference is to be connected  to ACS550 analog input 

AI1. The analog input can accept a voltage signal (0 – 10 VDC) or a current signal (0 

– 20 mA). Jumper J1, located on the Control Board in the ACS550, determines the 

signal type. J1 can be set in either the voltage or current position according to the 

type of external signal that will be connected. 

Refer to the ACS550-01/U1 User’s 

Manual.

Run Enable Interlocks

Run Enable interlocks are normally closed un-powered contacts connected in series 

between 1TB:7 and 1TB:8. When any of these contacts opens, the motor will stop, 

whether in DRIVE or BYPASS. The unit is shipped with a jumper installed from 

1TB:7 to 1TB:8. This jumper must be removed before connecting external contacts.

Summary of Contents for ACS550-CC






































Reviews: