ABB ACS 800 Series Installation Manual Download Page 27 | Manualshive

Page: 27 / 52

background image

Drive module of frame size R7 with bottom exit and Rittal cooling unit

27

Installation steps

Install the cooling unit according to the manufacturer’s instructions to the side panel
of the drive enclosure:

1. Cut openings in the side panel of the enclosure for air input and output and power

supply wiring of the cooling unit.

2. Install the cooling unit.
3. Lead the power supply wires through a lead-through grommet into the enclosure.
4. Connect the power supply wires and secure them with cable ties.

Connections in the
cooling unit:

Fastening bolt

Cutting in the side panel

View of the cooling unit power supply
wiring inside the enclosure

L1

L2

L3

400 VAC

«
...
25
26
27
28
29
...
»

Summary of Contents for ACS 800 Series





















































Reviews:

No comments

Related manuals for ACS 800 Series

Brand: Panasonic Pages: 2

Brand: IBS Pages: 24

Brand: Panasonic Pages: 1

OLYMPIA 3x3.05m/10

Brand: Palram Applications Pages: 65

Brand: Q-See Pages: 28

Brand: Eaton Pages: 11

HAZARDOUS ROOM Series

Brand: aci Pages: 3

Brand: aci Pages: 4

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: PRAXIS Pages: 2

UNAM 12N8910/S14OD

Brand: Baumer Pages: 3

Brand: Sport-Tec Pages: 22

Brand: Cerlic Pages: 20

Big Daddy Insta-Net

Brand: Izzo Golf Pages: 2

Brand: Pro-Ject Audio Systems Pages: 7

Brand: SOLAC Pages: 13

ecoCRAFT VKK GB 1206/3-E-H

Brand: Vaillant Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands