ABB ACS 800 Series Installation Manual Download Page 8

Page: 8 / 52

About this manual

describes the installation of a drive module of frame

size R8 in an 800 mm × 2000 mm × 600 mm enclosure.

contains the dimensional drawings of the fastening points in

the drive modules used in the installation examples in this manual, and dimensional
drawings of air baffles and EMC screens.

Other related manuals

Refer to

ACS800-04/04M/U4 Cabinet Installation

[3AFE68360323 (English)] for

information concerning the drive module such as

• dimensional drawings

• assembling instructions

• general instructions on installing the drive module into a cabinet.

Refer to

ACS800-04/04M/U4 Hardware Manual

[3AFE64671006 (English)] for

information concerning the drive module such as

• safety

• moving and unpacking

• specifications of the drive, e.g. the ratings, sizes and technical requirements,

provisions for fulfilling the requirements for CE and other markings, warranty
policy etc.

For installation of ACS800-04M components, refer to their manuals:

•

ARFI-10 EMC Filter Installation Guide

[3AFE68317941 (English)

•

RDCU Drive Control Unit Hardware Manual

[3AFE64636324 (English)]

•

RPMP-11/13 Control Panel Mounting Platform Kit Installation Guide

[3AFE68400643 (English)].

The manuals can be viewed on the Internet:

www.abb.com

under

Motors, drives

and power electronics / Drives / Document library.

Component lists

ACS800-04M and Rittal parts used in the installation examples are listed in the
manual. A list of other components, such as the contactor, switch fuse etc., is
included in

Modules Engineering Tool

www.abb.com

under

Motors, drives and

power electronics

Low Voltage AC Drives / Drives / Industrial drives,

modules

Summary of Contents for ACS 800 Series





















































Search results

Summary of Contents for ACS 800 Series

Reviews:

Related manuals for ACS 800 Series

Brands by name

Popular brands

ABB ACS 800 Series, Installation Manual

Search results

Summary of Contents for ACS 800 Series

Reviews:

Related manuals for ACS 800 Series

Brands by name

Popular brands