A B B A B I L I T Y
T M
ED G E I N D US T R I A L G AT E WAY
57
9
—
9.2 How to supply power and turn ON the product
WARNING!
ELECTRIC SHOCK HAZARD
Failure to supply power correctly or to follow all operating instructions correctly, may create an electric
shock hazard, which could result in personal injury or loss of life, and / or damage the equipment or
other property.
To avoid injuries and safely supply power to the product, complete the following steps:
1. Observe all the instructions for safety, installation, and operation.
2. Make sure your hands are dry.
3. Make sure that all the cables used:
• Are in good condition before using them.
• Meet the product requirements and comply with the relevant standards and regulations.
4. Position cables with care. Do not position cables in places where they may be trampled or
compressed by objects placed on them.
5. Make sure that the power-points and plugs are in good condition before using them.
6. Do not overload the power-points and plugs.
7. Make sure that the product maintains a proper grounding connection.
8. Use a power supply that meets the product requirements and complies with the relevant standards
and regulations. In case of uncertainties, contact the ABB Technical Support Team (for more
information see “How to Receive Technical Assistance”).
9. Connect power after the installation of the system has been completed.
10. Never connect or disconnect the cables with the system or the external apparatus switched ON.
To supply power and turn ON the ABB Ability™ Edge Industrial Gateway, complete the following steps:
1. Setup a DC power source that:
• Meets the ABB Ability™ Edge Industrial Gateway power requirements.
• Deliver a maximum current of 2 A.
2. Check the input voltage as close as possible to the Power IN connector. This is to compensate for
any cable losses, caused by cable length and other cable characteristics.
3. Make sure that the DC power source is turned OFF.
4. Setup an external 2 A fuse on the line coming from the negative terminal of the DC power source.
5. Connect the DC power source terminals (“Power IN +” and “Power IN -”) to Pins 1 and 2 of the Power
IN connector:
—
9.3 How to trigger a hardware reset of the product
To trigger a hardware reset of the ABB Ability™ Edge Industrial Gateway, push the reset pushbutton
available in the Service Panel.
—
Figure 19
—
Figure 20
Power IN +
Power IN –
Summary of Contents for Ability
