background image

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.1 Introduction

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

2

Safety

2.1

Introduction

Turbochargers manufactured by ABB reflect the state of the art. The respective safety and
health protection requirements are met. This ensures safe operation of the turbocharger.
Nevertheless, there may be some residual risks during operation of and work on the tur-
bocharger which:

¡

are caused by the turbocharger itself or its accessories.

¡

are caused by the operating equipment used or supplies and materials.

¡

are a consequence of insufficient compliance with safety instructions.

¡

are a consequence of insufficient or inappropriate performance of maintenance and in-
spection work.

The operating company is responsible for defining measures that regulate safe access to
and safe handling of the turbocharger.

All instructions contained in this chapter must be observed for safe and trouble-free opera-
tion of the turbocharger and during all work on the turbocharger.

All further safety instructions contained and specifically identified in every chapter of this
Operation Manual (

Definition of safety instructions 

13

) must also be observed.

2.2

CE conformity

Information

ABB turbochargers comply with the Machinery Directive 2006/42/EC and are partly com-
pleted machinery as defined by Article 2 g in this directive.

Page 

12

 / 

147

Summary of Contents for A170-M66























































































































































Reviews: