2600T Series Pressure transmitters |
OI/266/FF/ADD-EN Rev. B 71
Idx
Parameter
Data
Type
Size
Storage
Description / Range / Selections / Note
28
INTEG_TYPE
RW
S
U8
1
S
Defines the type of counting (up or down) and the type of r
esetting (demand or periodic)
0
Not Initialized
1
UP AUTO
2
UP DEM
3
DN AUTO
4
DN DEM
5
PERIODIC
6
DEMAND
7
PER & DEM
29
INTEG_OPTS
RW
S
B_STR
2
S
A bit string to configur
e the type of input (rate or accum.) used in each input, the flow dir
ection to be consider
ed in the totalization, the
status to be consider
ed in TOT
AL
and if the tota
lization r
esidue shall be used in the next batch
(only when I
NTEG_TYPE = UP_AUTO or DN_AUTO).
Bit 0
Input 1 Accumulate
Bit 1
Input 2 Accumulate
Bit 2
Flow Forwar
d
Bit 3
Flow Reverse
Bit 4
Use Uncertain
Bit 5
Use Bad
Bit 6
Carry
Bit 7
Add zer
o if Bad
Bit 8
Confirm Reset
Bit 9
Generate Reset Event
30
CLOCK_ERR
RW
S
FLT
4
S
0 or > 0
Establishes the period for periodic r
eset, in seconds
31
PRE_TRIP
RW
S
FLT
4
S
0 or > 0
Value used for the
OUT_PTRIP
setting. It adjusts the amount of mass, volume or energy that should
set OUT_PTRIP when the integration r
eaches
(TOT
AL_SP - PRE_TRIP)
when counting UP or
PRE_
TRIP
when counting DOWN. Expr
essed in
OUT_RANGE Unit
32
N_RESET
R
S
FLT
4
N
The number of r
esets is counted in the r
egister
N_RESET
. This counter can not be written or r
eset. It pr
ovides verification that the
TOT
AL has not been r
eset since
N_RESET
was last checked. The counter should r
oll over fr
om 999999 to 0.
33
PCT_INCL
R
S
FLT
4
D
This value is the % of the absolute net incr
ement with good status r
espect of the absolute net incr
ement r
egar
dless of the status.
34
GOOD_LIM
RW
S
FLT
4
S
If
PCT_INCL ≥ GOOD_LIM
and the mode is AUTO the status of the OUT is GOOD_NC otherwise check the other limit. Expr
essed in %
35
UNCER
T_LIM
RW
S
FLT
4
S
If
PCT_INCL ≥ UNCER
T_LIM
and the mode is AUTO the status of the OUT is UNCER
TAIN otherwise is BAD. Expr
essed in %
36
OP_CMD_INT
RW
S
U8
1
D
0
OFF
Operator r
eset command. Resets the totalizer
1
ON
37
OUT
AGE_LIM
RW
S
FLT
4
S
0 or > 0
The max, tolerated duration for power failur
e. This value is used by the host expr
essed in seconds
38
RESET_CONFIRM
RW
R
DS-66
2
N
0
OFF
If the Confirm Reset in the
INTEG_OPTS
is set, any further r
eset will be pr
evented until a logic 1 is not
received in input to the
RESET_CONFIRM
. If not connected it acts like a momentary dynamic parame
-
ter
. This ensur
es that a host has r
ecor
ded the snapshot values befor
e the next r
eset can occur
.
1
CONFIRM
39
UPDA
TE_EVT
R
R
DS-73
14
D
This alert is generated by any change to the static data
40
BLOCK_ALM
RW
R
DS-72
13
D
The block alarm is used for all configuration, har
dwar
e, connection failur
e or system pr
oblems in the block. The cause of the alert is
enter
ed in the subcode field. The first alert to become active will set the Active Status in the status parameter
. When the Unr
eported status
is clear
ed by the alert r
eporting task, another block alert may be r
eported without clearing the Active Status, if the subcode has changed