abaco systems XVR16 Series Hardware Reference Manual Download Page 103

Page: 103 / 151

Publication No.

500-9300007876-000

Rev. C.0

FPGA Registers 103

Table 8-64 SSD Availability Register (0x6B1)

Bit

R/W

Description

Default

7:0

SSD7:SSD0 availability

1 = SSD available

0 = SSD not available

Table 8-65 SSD Hardware Secure Erase Availability (0X6B2)

Bit

Description

Default

7:0

SSD7:0 Secure Erase capability

0 = Hardware Secure Erase not available

1 = Hardware Secure Erase available

When available, indicates that triggering a hardware

erase function will result in a secure erase algorithm

being executed.

(Hardware Secure Erase not currently available, but

maybe in the future)

0x00

Table 8-66 UART Enable Register (0x6B8)

Bit

R/W

Description

Default

7:0

R/W

COM8:1 UART Enable

1 = UART is enabled

0 = UART is disabled and will not respond to reads or

writes.

Table 8-67 COM Port Transceiver Enable Register (0x6BB)

Bit

R/W

Description

Default

7:0

R/W

COM8:1 Enable

1 = COM Port transceivers enabled

0 = COM Port transceivers disabled

Software should set this bit to a ‘1’ after the desired

COM port mode (i.e. RS232/RS422) is set.

Table 8-68 COM Port Mode Register (0x6BC)

Bit

R/W

Description

Default

7-4

R/W

COM8:1 mode

1 = COM Port transceiver in RS422 mode

0 = COM Port transceiver in RS232 mode

Summary of Contents for XVR16 Series
























































































































































Search results

Summary of Contents for XVR16 Series

Reviews:

abaco systems XVR16 Series, Hardware Reference Manual, Page: 103 / 151

Search results

Summary of Contents for XVR16 Series

Reviews: